[Free] 2017(July) EnsurePass Examcollection Cisco 200-120 Dumps with VCE and PDF 141-150

2017 July Cisco Official New Released 200-120
100% Free Download! 100% Pass Guaranteed!

CCNA Cisco Certified Network Associate CCNA

Question No: 141 – (Topic 4)

Refer to the exhibit.


For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.)

  1. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server.

  2. Router1 is acting as a TFTP server for other routers.

  3. Router1 cannot locate a valid IOS image in flash memory.

  4. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

  5. Cisco routers will first attempt to load an image from TFTP for management purposes.

Answer: A,C

Question No: 142 DRAG DROP – (Topic 4)




Question No: 143 – (Topic 4)

A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the configuration and issuing the show run command, the password for Telnet access should be encrypted. Which set of commands will accomplish this task?

  1. service password-encryption

    access-list 1 permit

    line vty 0 4 login

    password cisco access-class 1

  2. enable password secret line vty 0


    password cisco

  3. service password-encryption line vty 1


    password cisco

  4. service password-encryption line vty 0 4


password cisco

Answer: C

Question No: 144 – (Topic 4)

When a router undergoes the exchange protocol within OSPF, in what order does it pass through each state?

  1. exstart state gt; loading state gt; exchange state gt; full state

  2. exstart state gt; exchange state gt; loading state gt; full state

  3. exstart state gt; full state gt; loading state gt; exchange state

  4. loading state gt; exchange state gt; full state gt; exstart state

Answer: B

Question No: 145 – (Topic 4)

Refer to the exhibit.


What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two.)

  1. Router(config)# interface fastethernet 0/0 Router(config-if)# ip address Router(config-if)# no shut down

  2. Router(config)# interface fastethernet 0/0

    Router(config-if)# no shut down Router(config)# interface fastethernet 0/0.1 Router(config-subif)# encapsulation dot1q 10

    Router(config-subif)# ip address Router(config)# interface fastethernet 0/0.2

    Router(config-subif)# encapsulation dot1q 20

    Router(config-subif)# ip address

  3. Router(config)# router eigrp 100 Router(config-router)# network Router(config-router)# network

  4. Switch1(config)# vlan database Switch1(config-vlan)# vtp domain XYZ Switch1(config-vlan)# vtp server

  5. Switch1(config)# interface fastethernet 0/1 Switch1(config-if)# switchport mode trunk

  6. Switch1(config)# interface vlan 1 Switch1(config-if)# ip default-gateway

Answer: B,E

Question No: 146 – (Topic 4)

Which statement describes the process ID that is used to run OSPF on a router?

  1. It is globally significant and is used to represent the AS number.

  2. It is locally significant and is used to identify an instance of the OSPF database.

  3. It is globally significant and is used to identify OSPF stub areas.

  4. It is locally significant and must be the same throughout an area.

Answer: B

Question No: 147 – (Topic 4)

Which two are advantages of static routing when compared to dynamic routing? (Choose two.)

  1. Configuration complexity decreases as network size increases.

  2. Security increases because only the network administrator may change the routing table.

  3. Route summarization is computed automatically by the router.

  4. Routing tables adapt automatically to topology changes.

  5. An efficient algorithm is used to build routing tables, using automatic updates.

  6. Routing updates are automatically sent to neighbors.

  7. Routing traffic load is reduced when used in stub network links.

Answer: B,G

Question No: 148 – (Topic 4)

Why do large OSPF networks use a hierarchical design? (Choose three.)

  1. to decrease latency by increasing bandwidth

  2. to reduce routing overhead

  3. to speed up convergence

  4. to confine network instability to single areas of the network

  5. to reduce the complexity of router configuration

  6. to lower costs by replacing routers with distribution layer switches

Answer: B,C,D

Question No: 149 – (Topic 4)

What is the default administrative distance of OSPF?

A. 90 B. 100 C. 110 D. 120

Answer: C

Question No: 150 – (Topic 4)

Refer to the exhibit.


A network administrator configures a new router and enters the copy startup-config running-config command on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enters the system configuration dialog as shown. What is the cause of the problem?

  1. The network administrator failed to save the configuration.

  2. The configuration register is set to 0x2100.

  3. The boot system flash command is missing from the configuration.

  4. The configuration register is set to 0x2102.

  5. The router is configured with the boot system startup command.

Answer: A

100% Free Download!
Download Free Demo:200-120 Demo PDF
100% Pass Guaranteed!
Download 2017 EnsurePass 200-120 Full Exam PDF and VCE
Get 10% off your purchase! Copy it:TJDN-947R-9CCD [2017.07.01-2017.07.31]

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 EnsurePass IT Certification PDF and VCE

Leave a Reply