[Free] 2017(July) EnsurePass Examcollection Cisco 200-120 Dumps with VCE and PDF 171-180

EnsurePass
2017 July Cisco Official New Released 200-120
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/200-120.html

CCNA Cisco Certified Network Associate CCNA

Question No: 171 – (Topic 4)

Refer to the exhibit.

image

The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?

  1. 10.0.0.0/22 is subnetted, 1 subnets

    D 10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

  2. 10.0.0.0/28 is subnetted, 1 subnets

    D 10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

  3. 10.0.0.0/30 is subnetted, 1 subnets

    D 10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

  4. 10.0.0.0/22 is subnetted, 1 subnets

    D 10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

  5. 10.0.0.0/28 is subnetted, 1 subnets

    D 10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

  6. 10.0.0.0/30 is subnetted, 1 subnets

D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

Answer: D

Question No: 172 – (Topic 4)

Refer to the exhibit.

image

What can be determined about the router from the console output?

  1. No configuration file was found in NVRAM.

  2. No configuration file was found in flash.

  3. No configuration file was found in the PCMCIA card.

  4. Configuration file is normal and will load in 15 seconds.

Answer: A

Question No: 173 – (Topic 4)

Which command reveals the last method used to powercycle a router?

  1. show reload

  2. show boot

  3. show running-config

  4. show version

Answer: D

Question No: 174 – (Topic 4)

Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)

  1. Router(config)# router ospf 0

  2. Router(config)# router ospf 1

  3. Router(config)# router ospf area 0

  4. Router(config-router)# network 192.168.16.0 0.0.0.255 0

  5. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0

  6. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0

Answer: B,E

Question No: 175 – (Topic 4)

What two things will a router do when running a distance vector routing protocol? (Choose two.)

  1. Send periodic updates regardless of topology changes.

  2. Send entire routing table to all routers in the routing domain.

  3. Use the shortest-path algorithm to the determine best path.

  4. Update the routing table based on updates from their neighbors.

  5. Maintain the topology of the entire network in its database.

Answer: A,D

Question No: 176 – (Topic 4)

Refer to the exhibit.

image

When running OSPF, what would cause router A not to form an adjacency with router B?

  1. The loopback addresses are on different subnets.

  2. The values of the dead timers on the routers are different.

  3. Route summarization is enabled on both routers.

  4. The process identifier on router A is different than the process identifier on router B.

Answer: B

Question No: 177 – (Topic 4)

Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information? (Choose two.)

  1. the amount of available ROM

  2. the amount of available flash and RAM memory

  3. the version of the bootstrap software present on the router

  4. show version

  5. show processes

  6. show running-config

Answer: B,D

Question No: 178 – (Topic 4)

Refer to the exhibit.

image

Based on the exhibited routing table, how will packets from a host within the 192.168.10.192/26 LAN be forwarded to 192.168.10.1?

  1. The router will forward packets from R3 to R2 to R1.

  2. The router will forward packets from R3 to R1 to R2.

  3. The router will forward packets from R3 to R2 to R1 AND from R3 to R1.

  4. The router will forward packets from R3 to R1.

Answer: C

Question No: 179 – (Topic 4)

Which command shows your active Telnet connections?

  1. show cdp neigbors

  2. show session

  3. show users

  4. show vty logins

Answer: B

Question No: 180 – (Topic 4)

On a corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?

  1. a router with subinterfaces configured on the physical interface that is connected to the switch

  2. a router with an IP address on the physical interface connected to the switch

  3. a switch with an access link that is configured between the switches

  4. a switch with a trunk link that is configured between the switches

Answer: A

100% Free Download!
Download Free Demo:200-120 Demo PDF
100% Pass Guaranteed!
Download 2017 EnsurePass 200-120 Full Exam PDF and VCE
Get 10% off your purchase! Copy it:TJDN-947R-9CCD [2017.07.01-2017.07.31]

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 EnsurePass IT Certification PDF and VCE

Leave a Reply