[Free] 2017(July) EnsurePass Examcollection Cisco 200-125 Dumps with VCE and PDF 381-390

EnsurePass
2017 July Cisco Official New Released 200-125
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/200-125.html

CCNA Cisco Certified Network Associate CCNA (v3.0)

Question No: 381 – (Topic 8)

Which command can you enter to configure a local username with an encrypted password and EXEC mode user privileges?

  1. Router(config)#username jdone privilege 1 password 7 08314D5D1A48

  2. Router(config)#username jdone privilege 1 password 7 PASSWORD1

  3. Router(config)#username jdone privilege 15 password 0 08314D5D1A48

  4. Router(config)#username jdone privilege 15 password 0 PASSWORD1

Answer: A

Question No: 382 – (Topic 8)

Under normal operations, cisco recommends that you configure switch ports on which vlan ?

  1. on the default vlan

  2. on the management vlan

  3. on the native vlan

  4. on any vlan except the default vlan

Answer: D Explanation:

/Reference:

http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/24330- 185.html

Question No: 383 – (Topic 8)

Which WAN topology is most appropriate for a centrally located server farm with several satellite branches?

  1. star

  2. hub and spoke

  3. point-to-point

  4. full mesh

Answer: B

Explanation: Explanation/Reference:

In a Hub-and-spoke Site-to-Site Wide Area Network (WAN) network topology, one physical site act as Hub (Example, Main Office), while other physical sites act as spokes. Spoke sites are connected to each other via Hub site. In Huband-spoke Wide Area Network (WAN) topology, the network communication between two spokes always travels through the hub.

Question No: 384 – (Topic 8)

Which three statements about link-state routing are true? (Choose three.)

  1. Routes are updated when a change in topology occurs.

  2. Updates are sent to a multicast address by default.

  3. OSPF is a link-state protocol.

  4. Updates are sent to a broadcast address.

  5. RIP is a link-state protocol.

  6. It uses split horizon.

Answer: A,B,C

Question No: 385 – (Topic 8)

Which utility can you use to identify redundant or shadow rules ?

  1. The ACL trace tool in Cisco APIC-EM.

  2. The ACL analysis tool in Cisco APIC-EM.

  3. The Cisco APIC-EM automation scheduler.

  4. The Cisco IWAN application.

Answer: B

Question No: 386 – (Topic 8)

Which two statements about late collisions are true? (Choose two.)

  1. They may indicate a duplex mismatch.

  2. By definition, they occur after the 512th bit of the frame has been transmitted.

  3. They indicate received frames that did not pass the FCS match.

  4. They are frames that exceed 1518 bytes.

  5. They occur when CRC errors and interference occur on the cable.

Answer: A,B

Question No: 387 – (Topic 8)

which two options are the best reasons to use an ipv4 private ip space ?

  1. to manage routing overhead

  2. to implement nat

  3. to connect applications

  4. to enable intra enterprise communication

  5. to conserve global address space

Answer: C,E

Question No: 388 – (Topic 8)

Which protocol is the Cisco proprietary implementation of FHRP?

  1. HSRP

  2. VRRP

  3. GLBP

  4. CARP

Answer: A

Question No: 389 – (Topic 8)

Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)

image

  1. It ensures that data will be forwarded by RouterB.

  2. It provides stability for the OSPF process on RouterB.

  3. It specifies that the router ID for RouterB should be 10.0.0.1.

  4. It decreases the metric for routes that are advertised from RouterB.

  5. It indicates that RouterB should be elected the DR for the LAN.

Answer: B,C Explanation: Explanation

A loopback interface never comes down even if the link is broken so it provides stability for the OSPF process (for example we use that loopback interface as the router-id) –

The router-ID is chosen in the order below:

The highest IP address assigned to a loopback (logical) interface. If a loopback interface is not defined, the highest IP address of all active router’s physical interfaces will be chosen.

-gt; The loopback interface will be chosen as the router ID of RouterB 鈥?/p>

Question No: 390 – (Topic 8)

Which command can you enter to determine whether serial interface 0/2/0 has been configured using HDLC encapsulation?

  1. router#show platform

  2. router#show interfaces Serial 0/2/0

  3. router#show ip interface s0/2/0

  4. router#\show ip interface brief

Answer: C

100% Free Download!
Download Free Demo:200-125 Demo PDF
100% Pass Guaranteed!
Download 2017 EnsurePass 200-125 Full Exam PDF and VCE
Get 10% off your purchase! Copy it:TJDN-947R-9CCD [2017.07.01-2017.07.31]

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 EnsurePass IT Certification PDF and VCE

Leave a Reply